Do you have access to a computer with an sd card reader? I believe the best and safest thing to do is to connect it to a computer, create disk image from it and try ro use a data recovery tool in the image file.

Edit: if you only have the phone, maybe you could try looking for apps to copy a disk image from the sd card and to recover data or try using some terminal emulator or one of those apps that install a linux distro inside android to use the dd command and then use testdisk and photorec tools. I recommend the second option, because the tools are open sourc and well tested

So Flash memory works in blocks called pages. The pages contain a header that ends in a few bytes that says what the rest of the page maps to.

If the file was encrypted, you’re probably SOL. If it was not encrypted it may be possible to to recover some parts of the files. This is extremely advanced level data recovery. I only know the abstract basic principals and would likely struggle to figure this out and recover my own stuff if I ever needed to do this. I’ve only programmed microcontrollers and flash memory devices.

A micro SD card contains a small microcontroller and some blocks of flash memory, although the microcontroller is transparent to the user and operating system… unless hacking with needle probes in a lab.

So here’s the basics. Writing flash involves taking an entire Page of memory and zeroing it first. There is a tiny voltage booster circuit on the card that allows the page to get pulsed up and down in voltage a few times in order to completely zero the entire page without any remaining residuals. Once this is done and the entire page has been zeroed, only then is it possible to write the data into the bytes of the page.

If you want to change a single byte level value in an address that already contains a value, first the entire page is copied to a blank page in another location, then the old page is pulsed a few times, then each value is transferred back into the old page except that the new value that needed to be changed is now set to the new values.

This is the proper way to write flash at a basic level. If the power is lost in the middle of this cycle, the worst case scenario is that the new updated value was not written. The page in question should never be “missing” because the header record should always point to either the original or copied page. One of the two should always be present and complete… in a proper setup. Obviously, it might be faster to simply use some RAM to hold the page, erase the old page and rewrite it. I have no idea what size pages are in modern SD cards, but on hobby class microcontrollers I have used the pages were 4096 bytes, IIRC. My understanding is that most SD cards use an 8051 clone micro, so it is probably a similar size.

So here’s the thing, the bulk of the data is always there. Somewhere deep down inside you likely already knew this. It is why you’re supposed to overwrite an entire drive instead of the “quick” erase in most formatting tools. The quick erase is simply deleting a tiny header file that says what exists where on the drive. Similarly, some part of your SD card there is a page or few where the header has been screwed up. Your OS is looking at this header info and seeing a mismatch of garbled junk and saying f-that bs.

Generally, recovery would involve dumping the raw contents of the flash memory as hexadecimal, being super familiar with what you’re looking at and knowing how to find the page that is causing the error. Generally I assume you’d need to replace the bad page with a good header and it would then work. There are services for this kind of operation; data recovery. In practice, this has a few more layers of complication. Pages can be placed in different locations that enable wear leveling so one area of memory is not over utilized. There is also a table of bad blocks/pages that the micro knows to skip, and there is usually a bit or address in the page that is used to detect errors that may have occurred.

This is pretty much everything I know on the subject. Hopefully it helps you understand the abstract nature of what is happening. In the simplest of terms, flash memory is like writing a long essay with an ink pen and where you can not make mistakes or use whiteout. If you need to make a change, you must write out the entire page all over again. This process is what is so time critical that you must “eject” the drive.

Start by making a backup of all the data from the card. Do not do anything before making a backup

Plug it into a computer and see what the computer says.

I usually use Linux for that because it offers good error messages and I know the tools. But other operating systems might help, too.

And if you start writing to the card or executing recovery tools, make a backup / image first.

If the files are very important, maybe don’t tamper with it and ask for help. Like a repair shop, your local Linux community or any trustworthy computer expert friend.

The biggest enemy is probably encryption, if it’s encrypted. The files are definitely still there if you just ripped it out. In the old days you could just run a recovery program and get everything back.

As far as I know you are screwed but maybe using disks program in Linux can help you to fix if the header is broken but I am not sure. You will have to try by yourself.

Have a look at Spinrite. Works wonders on HDDs, and I believe a lot of development has gone on to cater for SSDs as well.

Idk if comments boost post but boost.

Edit: damn, I commented to give op more reach and got downvoted. 😂